How To Replace A Bathtub (For Beginners).
How To Replace A Bathtub (For Beginners).
Blog Article
Just how do you really feel in regards to A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a new one is also a moderately tough task. If the old bathtub is conveniently easily accessible, the job can relocate easily; if you need to open up a wall surface to remove the old tub as well as position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old bathtub and also set in the brand-new one. Make certain you have actually certified on your own for the task as well as fit attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to think about employing one before you start. Opportunities are you might require an expert plumber to make tube links.
This post will assist you install a brand-new tub in your restroom if you have actually currently purchased a new bathtub as well as don't require to alter the plan of your previous supply of water pipelines.
Your tools and also material list must comprise the following:
Getting ready for the Installation
To start with, the sustaining framework supplied with the bath needs to be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome because of the limited accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this process. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the tub in the needed placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub till the spirit level reads level.
To mount faucets, fit all-time low of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the water and examine all joints and new pipework for leakages as well as tighten them if required. Load the tub and likewise inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub must wait until the bath tub has been used a minimum of once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the producer provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be connected to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break an inflexible seal, causing the water to permeate the wall surface between the bathroom and also the tiling, resulting in issues with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break fairly early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is recommended to fit the tiles using water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I'm just very interested in How to Install a Bathtub Yourself and I am hoping you enjoyed the piece. Those who enjoyed our post kindly make sure you remember to share it. We enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.
Find Out More Report this page